Build a basic box-joint jig and learn the secrets for getting perfect results!

Basic box-joint jigs like this one have been around for a long time. After you finish building and adjusting the jig, learn how get the most from it.

To use this jig you will need a tablesaw, stackable dado set, and a calipers with dial or digital readout. We've found a dial calipers essential because box joints must be cut with exacting accuracy, because any minor error in the width or spacing of the individual "fingers," even .001", multiplies itself with every finger you cut.

For reasons of design and proportion, you typically make the individual "fingers" in box joints as wide as the thickness of the workpieces. In this article, we'll make a jig for cutting 14 " wide fingers in 14 "-thick stock (see the drawing below for the precise dimensions of the joints). For thicker or thinner stock you adjust the size of the jig's pin and the width and height of the dado cut accordingly.

Box Joint Intro.jpg

Step 1

Cut parts A, B, and C to the sizes shown in the Exploded View drawing below. Any flat and straight stock will do.

BJJ Step 1.jpg

Step 2

Adjust your dado set for a cut that's .001" wider than the joint fingers (.251" in our example). With stackable dado sets you can place commercially made shims between the cutters, or make your own shims from various papers (standard tablet paper measures .002-.005" thick, some tissue and waxed papers measure .001" thick). Check your adjustment by measure a test cut with your calipers as shown below. Raise the dado set 12 " above the tabletop.

BJJ Step 2.jpg

Step 3

Cut the notch that holds the pin in part A. Do this by holding part A against the miter gauge with part B beneath it as shown below. Do not cut into part B.

BJJ Step 3a.jpg

Step 4

Cut a 14 x 14 x 6" strip of hardwood that fits snugly into the notch you just cut in part A. (The strip should slip into place, yet fit tightly enough so it doesn't fall out.) Cut a 112 " pin from the strip and glue it into the notch, flush with the back of part A. Save the leftover strip. Screw part B to part A.

Step 5

Now, set your miter gauge for a 90° cut. Use the leftover strip to position the jig assembly on the miter gauge. Do this by aligning the jig pin 14 " from the path of the dado set as shown below. With the pin aligned, temporarily clamp the jig to the miter gauge, then affix the gauge to the jig with screws. Replace the miter gauge into its slot and cut through parts A and B. Attach the blade guard (C) centered behind the notch you just cut. During this and the following steps, apply pressure to the miter gauge to hold its bar firmly against the right side of the slot. This will keep its distance from the dado set consistent during cuts.

BJJ Step 5.jpg

Step 6

Position a piece of scrap stock as shown below, and cut a notch into the scrap piece. Position this notch over the pin and make another cut. Position that notch over the pin and repeat the cut. With your calipers, check the width of the fingers. They should be .001" under your desired finger width. (For our 14 " fingers the calipers should read .249".)

BJJ Step 6.jpg

Step 7

Chances are your jig will need some adjustment to achieve the necessary finger width. If the fingers are too wide, say .255" in our example, tap the end of the jig closest to the blade with a hammer as shown below. Make more test cuts and tapping adjustments as necessary. If the fingers are too narrow (.245" in our example), tap the other end of the jig. Even though the jig is screwed in place, the hammer taps will make these fine adjustments.

BJJ Step 7.jpg

Step 8

With your calipers, check the depth of the fingers in your scrap stock. Adjust the height of your blade until the depth reads .016" more than the width of your fingers (.266" in our example). This leaves the fingers long enough so you can sand them flush with the box later.

BJJ Step 8.jpg

Now, read instructions on how to use the jig.